Emtec Universal Remote Control 4in1 H140 Podręcznik Użytkownika Pobierz pdf (Strona 7)

Note: As you can dedicate any appliance (TV, DVD, SAT...) to the

VCR,DVDorSATkeys,youneedrsttoenterany4digitcodefor

thekindofapplianceyouwishtocontrol(foundinthecodebook,i.e.:

IfyouwanttoprogramaSATundertheVCRkey,enteranySATcode

foundinthecodebookandthenfollowthestepsbelow:

1. Turn on the device you want to control.

2. Press and hold SETUP (4) until the LED indicator (1) lights stea-

dily. Release SETUP button.

3. Press the mode button (3) that matches the equipment you wish to

control.TheLED(1)blinksonce.

4. PressPROG+(7)once.Afterafewsecondstheremotestarts

stepping through the code library (fast search, 1 code per second).

Whenthedeviceresponds,youcanpressPROG+(7)toswitchto

slowsearch(1codeper3seconds).Youcanstepbackbypressing

PROG-(7)(youcanstepforwardbypressingPROG+(7)incaseyou

wenttoofarback).Assoonasthedevicerespondsagain,pressthe

-ENTkey(15)tostorethecodeyoufound.

7) Brand search

If your brand is listed hereafter, you have the possibility to use the

brand search method (faster than the «manual» and the «automatic

code search»):

BRAND CODE

Philips/Radiola    1

Sony/Panasonic/JVC/SharpAkai/Toshiba/Daewoo 2

Thomson/Brandt    3

Telefunken/Saba/Normende   4

Grundig/Blaupunkt    5

Nokia/ITT     6

1. Turn on the device you want to control.

2. Press and hold SETUP (4) until the LED indicator (1) lights stea-

dily. Release SETUP button.

3. Pressthemodekey(3)thatmatchestheequipmentyouwantto

control (for example TV).

4. Enter the code corresponding to your brand, point the 4 in 1

Universal Remote Control in the direction of your equipment, press

onceonlyPROG+(7)continuetopointthe4in1UniversalRemote

Control at your equipment until the equipment changes channel. (The

remote control sends an IR signal every second. So please wait until

your equipment reacts). When your equipment does react, press on

thekeyENT(15)toconrm.Ifaccidentallyyoumissthecode,you

can stop the autosearch by pressing PROG – (7) and by repeatedly

pressingthiskeyreturntotherightcode.PressENT(15)toconrm.

8) Identifying codes found using the search procedure

1. Press and hold SETUP (4) until the LED indicator (1) lights stea-

dily. Release SETUP.

2. Pressthemodekey(4)fortheequipmentyouwanttoidentify(TV,

VCR,DVDorSAT).TheLEDblinksonce.

3. PressagainSETUP.TheLEDblinksonce.

4. Toidentifytherstdigitpresseachnumberbuttonfrom0–9(13)

untiltheLEDblinks.Thenumberyoupressedistherstdigitofthe

code.

5. Presseachnumberkeyfrom0–9asabovetondthesecondand

third digit.

7. Presseachnumberkeyfrom0–9asabovetondthefourthdigit.

When the fourth digit has been found the LED will go off. Don’t

forget to write down the code on the label of the battery compartment.

9) Volume Control

AdjustmentofALLvolumecontrolsunderaspecicmode

You can program the remote control so that the volume and mute

keyscontrolaspecicdevice(thevolumecontrolmustexistonthe

corresponding device). E.g. control of TV sound in TV mode, VCR

mode and SAT mode.

1. Press and hold SETUP (4) until the LED indicator (1) lights stea-

dily. Release SETUP.

2. PressandholdMUTE(10)untiltheLED(1)blinksonce.Release

MUTE.

3. Pressonceonthemodekey(TV,SAT,…)correspondingtothe

device whose volume will always be controlled by the VOL (8) and

MUTE(10)keys.

4. PresstheMUTE(10)keyonce.

Adjustment of the volume controls for EACH mode.

You can program the remote control so that the volume control is

functional for each mode selected (the volume control must exist on

the corresponding device). E.g. control of the television set sound in

TV mode, control of the SAT receiver sound in SAT mode,...

1. Press and hold SETUP (4) until the LED indicator (1) lights stea-

dily. Release SETUP.

2. PressandholdMUTE(10)untiltheLED(1)blinksonce.Release

MUTE.

3. Pressonceonthemodekey(TV,VCR,…)correspondingtothe

device whose volume will always be controlled by the VOL (8) and

1 2 3 4 5 6 7 8 9 10 11 12 ... 64 65

Komentarze do niniejszej Instrukcji

Brak uwag

Emtec Universal Remote Control 4in1 H140 Podręcznik Użytkownika Strona 7

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Zdalne sterowanie Emtec Universal Remote Control 4in1 H140